Tuesday, 8 March 2016

BGP PIC (Prefix Independent Converge) Edge for IP and MPLS-VPN

BGP Prefix independent convergence

Contents

BGP PIC Edge for IP and MPLS-VPN

The BGP PIC Edge for IP and MPLS-VPN feature improves BGP convergence after a network failure. This convergence is applicable to both core and edge failures and can be used in both IP and MPLS networks. The BGP PIC Edge for IP and MPLS-VPN feature creates and stores a backup/alternate path in the routing information base (RIB), forwarding information base (FIB), and Cisco Express Forwarding so that when a failure is detected, the backup/alternate path can immediately take over, thus enabling fast failover.

Note
In this document, the BGP PIC Edge for IP and MPLS-VPN feature is called BGP PIC.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for BGP PIC

  • Ensure that the Border Gateway Protocol (BGP) and the IP or Multiprotocol Label Switching (MPLS) network is up and running with the customer site connected to the provider site by more than one path (multihomed).
  • Ensure that the backup/alternate path has a unique next hop that is not the same as the next hop of the best path.
  • Enable the Bidirectional Forwarding Detection (BFD) protocol to quickly detect link failures of directly connected neighbors.

Restrictions for BGP PIC

The following restrictions apply to the BGP PIC feature:
  • With BGP Multipath, the BGP Prefix-Independent Convergence (PIC) feature is already supported.
  • In MPLS VPNs, the BGP PIC feature is not supported with MPLS VPN Inter-Autonomous Systems Option B.
  • The BGP PIC feature supports prefixes only for IPv4, IPv6, VPNv4, and VPNv6 address families.
  • The BGP PIC feature cannot be configured with Multicast or L2VPN Virtual Routing and Forwarding (VRF) address families.
  • If the route reflector is only in the control plane, then you do not need BGP PIC, because BGP PIC addresses data plane convergence.
  • When two PE devices become each other’s backup/alternate path to a CE device, traffic might loop if the CE device fails. Neither device will reach the CE device, and traffic will continue to be forwarded between the PE devices until the time-to-live (TTL) timer expires.
  • The BGP PIC feature does not support Nonstop Forwarding with Stateful Switchover (NSF/SSO). However, ISSU is supported if both Route Processors have the BGP PIC feature configured.
  • The BGP PIC feature solves the traffic forwarding only for a single network failure at both the edge and the core.
  • The BGP PIC feature does not work with the BGP Best External feature. If you try to configure the BGP PIC feature after configuring the BGP Best External feature, you receive an error.

Information About BGP PIC

Benefits of the BGP PIC Edge for IP and MPLS-VPN Feature

  • An additional path for failover allows faster restoration of connectivity if a primary path is invalid or withdrawn.
  • Reduction of traffic loss.
  • Constant convergence time so that the switching time is the same for all prefixes.
  • Starting with Cisco IOS XE Release 3.10S, both the Labeled Border Gateway Protocol (BGP) Prefix-Independent Convergence (PIC) feature and the Loop-Free Alternate (LFA) Fast Reroute (FRR) feature can be configured together on the Cisco ASR 903 router.

How BGP Converges Under Normal Circumstances

Under normal circumstances, BGP can take several seconds to a few minutes to converge after a network change. At a high level, BGP goes through the following process:
  1. BGP learns of failures through either Interior Gateway Protocol (IGP) or BFD events or interface events.
  2. BGP withdraws the routes from the routing information base (RIB), and the RIB withdraws the routes from the forwarding information base (FIB) and distributed FIB (dFIB). This process clears the data path for the affected prefixes.
  3. BGP sends withdraw messages to its neighbors.
  4. BGP calculates the next best path to the affected prefixes.
  5. BGP inserts the next best path for affected prefixes into the RIB, and the RIB installs them in the FIB and dFIB.
This process takes a few seconds or a few minutes to complete, depending on the latency of the network, the convergence time across the network, and the local load on the devices. The data plane converges only after the control plane converges.

How BGP PIC Improves Convergence

The BGP PIC functionality is achieved by an additional functionality in the BGP, RIB, Cisco Express Forwarding, and MPLS.
  • BGP Functionality
BGP PIC affects prefixes under IPv4 and VPNv4 address families. For those prefixes, BGP calculates an additional second best path, along with the primary best path. (The second best path is called the backup/alternate path.) BGP installs the best and backup/alternate paths for the affected prefixes into the BGP RIB. The backup/alternate path provides a fast reroute mechanism to counter a singular network failure. BGP also includes the alternate/backup path in its application programming interface (API) to the IP RIB.
  • RIB Functionality
For BGP PIC, RIB installs an alternate path per route if one is available. With the BGP PIC functionality, if the RIB selects a BGP route containing a backup/alternate path, it installs the backup/alternate path with the best path. The RIB also includes the alternate path in its API with the FIB.
  • Cisco Express Forwarding Functionality
With BGP PIC, Cisco Express Forwarding stores an alternate path per prefix. When the primary path goes down, Cisco Express Forwarding searches for the backup/alternate path in a prefix independent manner. Cisco Express Forwarding also listens to BFD events to rapidly detect local failures.
  • MPLS Functionality
MPLS Forwarding is similar to Cisco Express Forwarding, in that it stores alternate paths and switches to an the alternate path if the primary path goes down.
When the BGP PIC feature is enabled, BGP calculates a backup/alternate path per prefix and installs it into BGP RIB, IP RIB, and FIB. This improves convergence after a network failure. There are two types of network failures that the BGP PIC feature detects:
  • Core node/link failure (internal Border Gateway Protocol [iBGP] node failure): If a PE node/link fails, then the failure is detected through IGP convergence. IGP conveys the failure through the RIB to the FIB.
  • Local link/immediate neighbor node failure (external Border Gateway Protocol [eBGP] node/link failure): To detect a local link failure or eBGP single-hop peer node failure in less than a second, you must enable BFD. Cisco Express Forwarding looks for BFD events to detect a failure of an eBGP single-hop peer.

Convergence in the Data Plane

Upon detection of a failure, Cisco Express Forwarding detects the alternate next hop for all prefixes affected by the failure. The data plane convergence is achieved in subseconds depending on whether the BGP PIC implementation exists in the software or hardware.

Convergence in the Control Plane

Upon detection of failure, BGP learns about the failure through IGP convergence or BFD events and sends withdraw messages for the prefixes, recalculating the best and backup/alternate paths, and advertising the next best path across the network.

BGP Fast Reroute's Role in the BGP PIC Feature

BGP Fast Reroute (FRR) provides a best path and a backup/alternate path in BGP, RIB, and Cisco Express Forwarding. BGP FRR provides a very fast reroute mechanism into the RIB and Cisco Express Forwarding on the backup BGP next hop to reach a destination when the current best path is not available.
BGP FRR precomputes a second best path in BGP and gives it to the RIB and Cisco Express Forwarding as a backup/alternate path, and Cisco Express Forwarding programs it into line cards.
Therefore, BGP FRR sets up the best path and backup/alternate path. The BGP PIC feature provides the ability for Cisco Express Forwarding to quickly switch the traffic to the other egress ports if the current next hop or the link to this next hop goes down. This is illustrated in the figure below.
Figure 1. BGP PIC Edge and BGP FRR

How a Failure Is Detected

A failure in the iBGP (remote) peer is detected by IGP; it may take a few seconds to detect the failure. Convergence can occur in subseconds or seconds, depending on whether PIC is enabled on the line cards.
If the failure is with directly connected neighbors (eBGP), and if you use BFD to detect when a neighbor has gone down, the detection happens within a subsecond and the convergence can occur in subseconds or seconds, depending on whether PIC is enabled on the line cards.

How BGP PIC Can Achieve Subsecond Convergence

The BGP PIC feature works at the Cisco Express Forwarding level, and Cisco Express Forwarding can be processed in both hardware line cards and in the software.
  • For platforms that support Cisco Express Forwarding processing in the line cards, the BGP PIC feature can converge in subseconds.
  • For platforms that do not use Cisco Express Forwarding in hardware line cards, Cisco Express Forwarding is achieved in the software. The BGP PIC feature works with the Cisco Express Forwarding through the software and achieves convergence within seconds.

How BGP PIC Improves Upon the Functionality of MPLS VPN BGP Local Convergence

The BGP PIC feature is an enhancement to the "MPLS VPN--BGP Local Convergence" feature, which provides a failover mechanism that recalculates the best path and installs the new path in forwarding after a link failure. The feature maintains the local label for 5 minutes to ensure that the traffic uses the backup/alternate path, thus minimizing traffic loss.
The BGP PIC feature improves the LoC time to under a second by calculating a backup/alternate path in advance. When a link failure occurs, the traffic is sent to the backup/alternate path.
When you configure the BGP PIC feature, it will override the functionality of the "MPLS VPN--BGP Local Convergence" feature. You do not have to remove the protection local-prefixes command from the configuration.

Configuration Modes for Enabling BGP PIC

Because many service provider networks contain many VRFs, the BGP PIC feature allows you to configure the BGP PIC feature for all VRFs at once.
  • VPNv4 address family configuration mode protects all the VRFs.
  • VRF-IPv4 address family configuration mode protects only IPv4 VRFs.
  • Router configuration mode protects prefixes in the global routing table.

BGP PIC Scenarios

The following scenarios explain how you can configure the BGP PIC functionality to achieve fast convergence:

IP PE-CE Link and Node Protection on the CE Side (Dual PEs)

The figure below shows a network that uses the BGP PIC feature. The network includes the following components:
  • eBGP sessions exist between the PE and CE devices.
  • Traffic from CE1 uses PE1 to reach network 192.168.9.0/24 through device CE3.
  • CE1 has two paths:
    • PE1 as the primary path.
    • PE2 as the backup/alternate path.
CE1 is configured with the BGP PIC feature. BGP computes PE1 as the best path and PE2 as the backup/alternate path and installs both routes into the RIB and Cisco Express Forwarding plane. When the CE1-PE1 link goes down, Cisco Express Forwarding detects the link failure and points the forwarding object to the backup/alternate path. Traffic is quickly rerouted due to local fast convergence in Cisco Express Forwarding.
Figure 2. Using BGP PIC to Protect the PE-CE Link

IP PE-CE Link and Node Protection on the CE Side (Dual CEs and Dual PE Primary and Backup Nodes)

The figure below shows a network that uses the BGP PIC feature on CE1. The network includes the following components:
  • eBGP sessions exist between the PE and CE devices.
  • Traffic from CE1 uses PE1 to reach network 192.168.9.0/24 through device CE3.
  • CE1 has two paths:
    • PE1 as the primary path.
    • PE2 as the backup/alternate path.
  • An iBGP session exists between the CE1 and CE2 devices.
In this example, CE1 and CE2 are configured with the BGP PIC feature. BGP computes PE1 as the best path and PE2 as the backup/alternate path and installs both the routes into the RIB and Cisco Express Forwarding plane.
There should not be any policies set on CE1 and CE2 for the eBGP peers PE1 and PE2. Both CE devices must point to the eBGP route as next hop. On CE1, the next hop to reach CE3 is through PE1, so PE1 is the best path to reach CE3. On CE2, the best path to reach CE3 is PE2. CE2 advertises itself as the next hop to CE1, and CE1 does the same to CE2. As a result, CE1 has two paths for the specific prefix and it usually selects the directly connected eBGP path over the iBGP path according to the best path selection rules. Similarly, CE2 has two paths--an eBGP path through PE2 and an iBGP path through CE1-PE1.
When the CE1-PE1 link goes down, Cisco Express Forwarding detects the link failure and points the forwarding object to the backup/alternate node CE2. Traffic is quickly rerouted due to local fast convergence in Cisco Express Forwarding.
If the CE1-PE1 link or PE1 goes down and BGP PIC is enabled on CE1, BGP recomputes the best path, removing the next hop PE1 from RIB and reinstalling CE2 as the next hop into the RIB and Cisco Express Forwarding. CE1 automatically gets a backup/alternate repair path into Cisco Express Forwarding and the traffic loss during forwarding is now in subseconds, thereby achieving fast convergence.
Figure 3. Using BGP PIC in a Dual CE, Dual PE Network

IP MPLS PE-CE Link Protection for the Primary or Backup Alternate Path

The figure above shows a network that uses the BGP PIC feature on CE1 and CE2. The network includes the following components:
  • eBGP sessions exist between the PE and CE devices.
  • The PE devices are VPNv4 iBGP peers with reflect devices in the MPLS network.
  • Traffic from CE1 uses PE1 to reach network 192.168.9.0/24 through device CE3.
  • CE3 is dual-homed with PE3 and PE4.
  • PE1 has two paths to reach CE3 from the reflect routers:
    • PE3 is the primary path with the next hop as a PE3 address.
    • PE4 is the backup/alternate path with the next hop as a PE4 address.
In this example, all the PE devices can be configured with the BGP PIC feature under IPv4 or VPNv4 address families.
For BGP PIC to work in BGP for PE-CE link protection, set the policies on PE3 and PE4 for prefixes received from CE3 so that one of the PE devices acts as the primary and the other as the backup/alternate. Usually, this is done using local preference and giving better local preference to PE3. In the MPLS cloud, traffic internally flows through PE3 to reach CE3. Thus, PE1 has PE3 as the best path and PE4 as the second path.
When the PE3-CE3 link goes down, Cisco Express Forwarding detects the link failure, and PE3 recomputes the best path, selects PE4 as the best path, and sends a withdraw message for the PE3 prefix to the reflect routers. Some of the traffic goes through PE3-PE4 until BGP installs PE4 as the best path route into the RIB and Cisco Express Forwarding. PE1 receives the withdraw, recomputes the best path, selects PE4 as the best path, and installs the routes into the RIB and Cisco Express Forwarding plane.
Thus, with BGP PIC enabled on PE3 and PE4, Cisco Express Forwarding detects the link failure and does in-place modification of the forwarding object to the backup/alternate node PE4 that already exists in Cisco Express Forwarding. PE4 knows that the backup/alternate path is locally generated and routes the traffic to the egress port connected to CE3. This way, traffic loss is minimized and fast convergence is achieved.

IP MPLS PE-CE Node Protection for Primary or Backup Alternate Path

The figure below shows a network that uses the BGP PIC feature on all the PE devices in an MPLS network.
Figure 4. Enabling BGP PIC on all PEs devices in the MPLS Network

The network includes the following components:
  • eBGP sessions exist between the PE and CE devices.
  • The PE devices are VPNv4 iBGP peers with reflect routers in the MPLS network.
  • Traffic from CE1 uses PE1 to reach network 192.168.9.0/24 through device CE3.
  • CE3 is dual-homed with PE3 and PE4.
  • PE1 has two paths to reach CE3 from the reflect routers:
    • PE3 is the primary path with the next hop as a PE3 address.
    • PE4 is the backup/alternate path with the next hop as a PE4 address.
In this example, all the PE devices are configured with the BGP PIC feature under IPv4 and VPNv4 address families.
For BGP PIC to work in BGP for the PE-CE node protection, set the policies on PE3 and PE4 for the prefixes received from CE3 such that one of the PE devices acts as primary and the other as backup/alternate. Usually, this is done using local preference and giving better local preference to PE3. In the MPLS cloud, traffic internally flows through PE3 to reach CE3. So, PE1 has PE3 as the best path and PE4 as the second path.
When PE3 goes down, PE1 knows about the removal of the host prefix by IGPs in subseconds, recomputes the best path, selects PE4 as the best path, and installs the routes into the RIB and Cisco Express Forwarding plane. Normal BGP convergence will happen while BGP PIC is redirecting the traffic through PE4, and packets are not lost.
Thus, with BGP PIC enabled on PE3, Cisco Express Forwarding detects the node failure on PE3 and points the forwarding object to the backup/alternate node PE4. PE4 knows that the backup/alternate path is locally generated and routes the traffic to the egress port using the backup/alternate path. This way, traffic loss is minimized.
No Local Policies Set on the PE Devices
PE1 and PE2 point to the eBGP CE paths as the next hop with no local policy. Each of the PE devices receives the other’s path, and BGP calculates the backup/alternate path and installs it into Cisco Express Forwarding, along with its own eBGP path towards CE as the best path. The limitation of the MPLS PE-CE link and node protection solutions is that you cannot change BGP policies. They should work without the need for a best-external path.
Local Policies Set on the PE Devices
Whenever there is a local policy on the PE devices to select one of the PE devices as the primary path to reach the egress CE, the bgp advertise-best-external command is needed on the backup/alternate node PE3 to propagate the external CE routes with a backup/alternate label into the route reflectors and the far-end PE devices.

Cisco Express Forwarding Recursion

Recursion is the ability to find the next longest matching path when the primary path goes down.
When the BGP PIC feature is not installed, and if the next hop to a prefix fails, Cisco Express Forwarding finds the next path to reach the prefix by recursing through the FIB to find the next longest matching path to the prefix. This is useful if the next hop is multiple hops away and there is more than one way of reaching the next hop.
However, with the BGP PIC feature, you may want to disable Cisco Express Forwarding recursion for the following reasons:
  • Recursion slows down convergence when Cisco Express Forwarding searches all the FIB entries.
  • BGP PIC Edge already precomputes an alternate path, thus eliminating the need for Cisco Express Forwarding recursion.
When the BGP PIC functionality is enabled, Cisco Express Forwarding recursion is disabled by default for two conditions:
  • For next hops learned with a /32 network mask (host routes)
  • For next hops that are directly connected
For all other cases, Cisco Express Forwarding recursion is enabled.
As part of the BGP PIC functionality, you can issue the bgp recursion host command to disable or enable Cisco Express Forwarding recursion for BGP host routes.

Note
When the BGP PIC feature is enabled, by default, bgp recursion host is configured for VPNv4 and VPNv6 address families and disabled for IPv4 and IPv6 address families.
To disable or enable Cisco Express Forwarding recursion for BGP directly connected next hops, you can issue the disable-connected-check command.

How to Configure BGP PIC

Configuring BGP PIC

Because many service provider networks contain many VRFs, the BGP PIC feature allows you to configure the BGP PIC feature for all VRFs at once.
  • VPNv4 address family configuration mode protects all the VRFs.
  • VRF-IPv4 address family configuration mode protects only IPv4 VRFs.
  • Router configuration mode protects prefixes in the global routing table.
For a full configuration example that includes configuring multiprotocol VRFs and shows output to verify that the feature is enabled, see the Example: Configuring BGP PIC.
Before You Begin
  • If you are implementing the BGP PIC feature in an MPLS VPN, ensure that the network is working properly before configuring the BGP PIC feature. See “Configuring MPLS Layer 3 VPNs” for more information.
  • If you are implementing the BGP PIC feature in an MPLS VPN, configure multiprotocol VRFs, which allow you to share route-target policies (import and export) between IPv4 and IPv6 or to configure separate route-target policies for IPv4 and IPv6 VPNs. For information about configuring multiprotocol VRFs, see “MPLS VPN—VRF CLI for IPv4 and IPv6 VPNs”.
  • Ensure that the CE device is connected to the network by at least two paths.
SUMMARY STEPS
    1.    enable
    2.    configure terminal
    3.    router bgp autonomous-system-number
    4.    Do one of the following:
    • address-family ipv4 [unicast | vrf vrf-name]
    • address-family vpnv4 [unicast]
    5.    bgp additional-paths install
    6.    neighbor ip-address remote-as autonomous-system-number
    7.    neighbor ip-address activate
    8.    bgp recursion host
    9.    neighbor ip-address fall-over [bfd |route-map map-name]
    10.    end

DETAILED STEPS
 Command or ActionPurpose
Step 1 enable


Example: 
Device> enable
  		Enables privileged EXEC mode.
  • Enter your password if prompted.
 
Step 2 configure terminal


Example: 
Device# configure terminal
  		Enters global configuration mode.
 
Step 3 router bgp autonomous-system-number


Example: 
Device(config)# router bgp 40000
  		Enters router configuration mode for the specified routing process.
 
Step 4Do one of the following:
  • address-family ipv4 [unicast | vrf vrf-name]
  • address-family vpnv4 [unicast]


Example: 
Device(config-router)# address-family ipv4 unicast


Example: 
Device(config-router)# address-family vpnv4
  		Specifies the IPv4 or VPNv4 address family and enters address family configuration mode.
  • The unicast keyword specifies the IPv4 or VPNv4 unicast address family.
  • The vrf keyword and vrf-name argument specify the name of the virtual routing and forwarding (VRF) instance to associate with subsequent IPv4 address family configuration mode commands.
 
Step 5 bgp additional-paths install


Example: 
Device(config-router-af)# bgp additional-paths install
  		Calculates a backup/alternate path and installs it into the RIB and Cisco Express Forwarding.
 
Step 6 neighbor ip-address remote-as autonomous-system-number


Example: 
Device(config-router-af)# neighbor 192.168.1.1 remote-as 45000
  		Adds the IP address of the neighbor in the specified autonomous system to the IPv4 multiprotocol BGP neighbor table of the local router.
  • By default, neighbors that are defined using the neighbor remote-as command in router configuration mode exchange only IPv4 unicast address prefixes. To exchange other address prefix types, neighbors must also be activated using the neighbor activate command in address family configuration mode for the other prefix types.
 
Step 7 neighbor ip-address activate


Example: 
Device(config-router-af)# neighbor 192.168.1.1 activate
  		Enables the neighbor to exchange prefixes for the IPv4 unicast address family with the local router.
 
Step 8 bgp recursion host


Example: 
Device(config-router-af)# bgp recursion host
  		(Optional) Enables the recursive-via-host flag for IPv4, VPNv4, and VRF address families.
  • When the BGP PIC feature is enabled, Cisco Express Forwarding recursion is disabled. Under most circumstances, you do not want to enable recursion when BGP PIC is enabled.
 
Step 9 neighbor ip-address fall-over [bfd |route-map map-name]


Example: 
Device(config-router-af)# neighbor 192.168.1.1 fall-over bfd
  		Enables BFD protocol support to detect when a neighbor has gone away, which can occur within a subsecond.
 
Step 10 end


Example: 
Device(config-router-af)# end
  		Exits address family configuration mode and returns to privileged EXEC mode.
 

Disabling BGP PIC Core

BGP PIC core feature is enabled by default. Use the following configuration to disable the BGP PIC core feature.

Note
Use the cef table output-chain build favor convergence-speed command in global configuration mode to re-enable the BGP PIC core feature.
SUMMARY STEPS
    1.    enable
    2.    configure terminal
    3.    cef table output-chain build favor memory-utilization
    4.    end

DETAILED STEPS
 Command or ActionPurpose
Step 1 enable


Example:
Device> enable
  		Enables privileged EXEC mode.
  • Enter your password if prompted.
 
Step 2 configure terminal


Example:
Device# configure terminal
  		Enters global configuration mode.
 
Step 3 cef table output-chain build favor memory-utilization


Example:
Device(config)# cef table output-chain build favor memory-utilization
  		Configures memory characteristics for Cisco Express Forwarding table output chain building for the forwarding of packets through the network.
 
Step 4 end


Example:
Device(config)# end
  		Exits global configuration mode and returns to privileged EXEC mode.
 

Configuration Examples for BGP PIC

Example: Configuring BGP PIC

The following example shows how to configure the BGP PIC feature in VPNv4 address family configuration mode, which enables the feature on all VRFs. In the following example, there are two VRFs defined: blue and green. All the VRFs, including those in VRFs blue and green, are protected by backup/alternate paths. 
vrf definition test1
 rd 400:1
 route-target export 100:1
 route-target export 200:1
 route-target export 300:1
 route-target export 400:1
 route-target import 100:1
 route-target import 200:1
 route-target import 300:1
 route-target import 400:1
 address-family ipv4
 exit-address-family
 exit
!
interface GigabitEthernet 0/0/0
 vrf forwarding test1
 ip address 10.0.0.1 255.0.0.0
 exit
router bgp 3
 no synchronization
 bgp log-neighbor-changes
 redistribute static
 redistribute connected
 neighbor 10.6.6.6 remote-as 3
 neighbor 10.6.6.6 update-source Loopback0
 neighbor 10.7.7.7 remote-as 3
 neighbor 10.7.7.7 update-source Loopback0
 no auto-summary
 !
 address-family vpnv4
  bgp additional-paths install
  neighbor 10.6.6.6 activate
  neighbor 10.6.6.6 send-community both
  neighbor 10.7.7.7 activate
  neighbor 10.7.7.7 send-community both
 exit-address-family
 !
 address-family ipv4 vrf blue
  import path selection all
  import path limit 10
  no synchronization
  neighbor 10.11.11.11 remote-as 1
  neighbor 10.11.11.11 activate
 exit-address-family
 !
 address-family ipv4 vrf green
  import path selection all
  import path limit 10
  no synchronization
  neighbor 10.13.13.13 remote-as 1
  neighbor 10.13.13.13 activate
 exit-address-family
The following show vrf detail command output shows that the BGP PIC feature is enabled: 
Router# show vrf detail
VRF test1 (VRF Id = 1); default RD 400:1; default VPNID <not set>
  Interfaces:
    Se4/0                   
Address family ipv4 (Table ID = 1 (0x1)):
  Export VPN route-target communities
    RT:100:1                 RT:200:1                 RT:300:1
    RT:400:1                
  Import VPN route-target communities
    RT:100:1                 RT:200:1                 RT:300:1
    RT:400:1                
  No import route-map
  No export route-map
  VRF label distribution protocol: not configured
  VRF label allocation mode: per-prefix
  Prefix protection with additional path enabled
Address family ipv6 not active.

Example: Displaying Backup Alternate Paths for BGP PIC

The command output in the following example shows that the VRFs in VRF blue have backup/alternate paths: 
Device# show ip bgp vpnv4 vrf blue 10.0.0.0

BGP routing table entry for 10:12:12.0.0.0/24, version 88
Paths: (4 available, best #1, table blue)
  Additional-path
  Advertised to update-groups:
     6         
  1, imported path from 12:23:12.0.0.0/24
    10.3.3.3 (metric 21) from 10.6.6.6 (10.6.6.6)
      Origin incomplete, metric 0, localpref 200, valid, internal, best
      Extended Community: RT:12:23
      Originator: 10.3.3.3, Cluster list: 10.0.0.1 , recursive-via-host
      mpls labels in/out nolabel/37
  1, imported path from 12:23:12.0.0.0/24
    10.13.13.13 (via green) from 10.13.13.13 (10.0.0.2)
      Origin incomplete, metric 0, localpref 100, valid, external
      Extended Community: RT:12:23 , recursive-via-connected
  1, imported path from 12:23:12.0.0.0/24
    10.3.3.3 (metric 21) from 10.7.7.7 (10.7.7.7)
      Origin incomplete, metric 0, localpref 200, valid, internal
      Extended Community: RT:12:23
      Originator: 10.3.3.3, Cluster list: 10.0.0.1 , recursive-via-host
      mpls labels in/out nolabel/37
  1
    10.11.11.11 from 10.11.11.11 (1.0.0.1)
      Origin incomplete, metric 0, localpref 100, valid, external, backup/repair
      Extended Community: RT:11:12 , recursive-via-connected
The command output in the following example shows that the VRFs in VRF green have backup/alternate paths: 
Device# show ip bgp vpnv4 vrf green 12.0.0.0

BGP routing table entry for 12:23:12.0.0.0/24, version 87
Paths: (4 available, best #4, table green)
  Additional-path
  Advertised to update-groups:
     5         
  1, imported path from 11:12:12.0.0.0/24
    10.11.11.11 (via blue) from 10.11.11.11 (1.0.0.1)
      Origin incomplete, metric 0, localpref 100, valid, external
      Extended Community: RT:11:12 , recursive-via-connected
  1
    10.3.3.3 (metric 21) from 10.7.7.7 (10.7.7.7)
      Origin incomplete, metric 0, localpref 200, valid, internal
      Extended Community: RT:12:23
      Originator: 10.3.3.3, Cluster list: 10.0.0.1 , recursive-via-host
      mpls labels in/out nolabel/37
  1
    10.13.13.13 from 10.13.13.13 (10.0.0.2)
      Origin incomplete, metric 0, localpref 100, valid, external, backup/repair
      Extended Community: RT:12:23 , recursive-via-connected
  1
    10.3.3.3 (metric 21) from 10.6.6.6 (10.6.6.6)
      Origin incomplete, metric 0, localpref 200, valid, internal, best
      Extended Community: RT:12:23
      Originator: 10.3.3.3, Cluster list: 10.0.0.1 , recursive-via-host
      mpls labels in/out nolabel/37
The command output in the following example shows the BGP routing table entries for the backup and alternate paths: 
Device# show ip bgp 10.0.0.0 255.255.0.0

BGP routing table entry for 10.0.0.0/16, version 123
Paths: (4 available, best #3, table default)
  Additional-path
  Advertised to update-groups:
     2          3         
  Local
    10.0.101.4 from 10.0.101.4 (10.3.3.3)
      Origin IGP, localpref 100, weight 500, valid, internal
  Local
    10.0.101.3 from 10.0.101.3 (10.4.4.4)
      Origin IGP, localpref 100, weight 200, valid, internal
  Local
    10.0.101.2 from 10.0.101.2 (10.1.1.1)
      Origin IGP, localpref 100, weight 900, valid, internal, best
  Local
    10.0.101.1 from 10.0.101.1 (10.5.5.5)
      Origin IGP, localpref 100, weight 700, valid, internal, backup/repair
The command output in the following example shows the routing information base entries for the backup and alternate paths: 
Device# show ip route repair-paths 10.0.0.0 255.255.0.0

Routing entry for 10.0.0.0/16
  Known via "bgp 10", distance 200, metric 0, type internal
  Last update from 10.0.101.2 00:00:56 ago
  Routing Descriptor Blocks:
  * 10.0.101.2, from 10.0.101.2, 00:00:56 ago
      Route metric is 0, traffic share count is 1
      AS Hops 0
      MPLS label: none
    [RPR]10.0.101.1, from 10.0.101.1, 00:00:56 ago
      Route metric is 0, traffic share count is 1
      AS Hops 0
      MPLS label: none
The command output in the following example shows the Cisco Express Forwarding/forwarding information base entries for the backup and alternate paths: 
Device# show ip cef 10.0.0.0 255.255.0.0 detail

10.0.0.0/16, epoch 0, flags rib only nolabel, rib defined all labels
  recursive via 10.0.101.2
    attached to GigabitEthernet0/2
  recursive via 10.0.101.1, repair
    attached to GigabitEthernet0/2

Example: Disabling BGP PIC Core

The following example shows how to disable the BGP PIC core in global configuration mode.
Device> enable
Device# configure terminal
Device(config)# cef table output-chain build favor memory-utilization
Device(config)# end

Additional References

Related Topic
Document Title
Cisco IOS commands
Cisco IOS Master Command List, All Releases
BGP commands
Cisco IOS IP Routing: BGP Command Reference
Basic MPLS VPNs
“Configuring MPLS Layer 3 VPNs” module in the MPLS: Layer 3 VPNs Configuration Guide
A failover feature that creates a new path after a link or node failure
“MPLS VPN—BGP Local Convergence” module in the MPLS: Layer 3 VPNs Configuration Guide
Configuring multiprotocol VRFs
“MPLS VPN—VRF CLI for IPv4 and IPv6 VPNs” module in the MPLS: Layer 3 VPNs Configuration Guide

Related Documents

Standards

Standard
Title
draft-walton-bgp-add-paths-04.txt
Advertisement of Multiple Paths in BGP

MIBs

MIB
MIBs Link
—
To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:
http:/​/​www.cisco.com/​go/​mibs

RFCs

RFC
Title
RFC 1771
A Border Gateway Protocol 4 (BGP-4)
RFC 2547
BGP/MPLS VPNs

Technical Assistance

Description
Link
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

Feature Information for BGP PIC

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.
Table 1 Feature Information for BGP PIC
Feature Name
Releases
Feature Information
BGP PIC Edge for IP and MPLS-VPN
Cisco IOS XE Release 3.2S
Cisco IOS XE Release 3.7S
The BGP PIC Edge for IP and MPLS-VPN feature improves BGP convergence after a network failure. This convergence is applicable to both core and edge failures and can be used in both IP and MPLS networks. The BGP PIC Edge for IP and MPLS-VPN feature creates and stores a backup/alternate path in the routing information base (RIB), forwarding information base (FIB), and Cisco Express Forwarding so that when a failure is detected, the backup/alternate path can immediately take over, thus enabling fast failover.
In Cisco IOS XE Release 3.2S, this feature was introduced.
The following commands were introduced or modified: bgp additional-paths install, bgp recursion host, show ip bgp, show ip cef, show ip route, show vrf.
In Cisco IOS XE Release 3.7S, support was added for the Cisco ASR 903 router.
Posted by at
Labels: ,